Flexible, highly efficient multimodal energy harvesting

A 10-fold increase in the ability to harvest mechanical and thermal energy over standard piezoelectric composites may be possible using a piezoelectric ceramic foam supported by a flexible polymer support, according to Penn State researchers.

In the search for ways to harvest small amounts of energy to run mobile electronic devices or sensors for health monitoring, researchers typically add hard ceramic nanoparticles or nanowires to a soft, flexible polymer support. The polymer provides the flexibility, while the piezo nanoparticles convert the mechanical energy into electrical voltage. But these materials are relatively inefficient, because upon mechanical loading the mechanical energy is largely absorbed by the bulk of the polymer, with a very small fraction transferred to the piezo nanoparticles. While adding more ceramic would increase the energy efficiency, it comes with the tradeoff of less flexibility.

"The hard ceramics in the soft polymer is like stones in water," said Qing Wang, professor of materials science and engineering, Penn State. "You can slap the surface of the water, but little force is transferred to the stones. We call that strain-transfer capability."

Almost three decades ago, the late Penn State materials scientist Bob Newnham came up with the concept that the connectivity of the piezo filler determined the efficiency of the piezoelectric effect. A three-dimensional material would be more efficient than what he classified as zero-dimensional nanoparticles, one-dimensional nanowires or two-dimensional films, because the mechanical energy would be transported directly through the three-dimensional material instead of dissipating into the polymer matrix.

"Bob Newnham was a legend in the field of piezoelectrics," said Wang. "so everybody in the ceramic community knew of his approach, but how to achieve that 3-D structure with a well-defined microstructure remained a mystery."

The secret ingredient to solve the mystery turned out to be a cheap polyurethane foam dusting sheet that can be purchased at any home improvement store. The small uniform protrusions on the sheet act as a template for forming the microstructure of the piezoelectric ceramic.

The researchers applied the ceramic to the polyurethane sheet in the form of suspended nanoparticles in solution. When the template and solution are heated to a high enough temperature, the sheet burns out and the solution crystalizes into a solid 3-D microform foam with uniform holes. They then fill the holes in the ceramic foam with polymer.

"We see that this 3-D composite has a much higher energy output under different modes," said Wang. "We can stretch it, bend it, press it. And at the same time, it can be used as a pyroelectric energy harvester if there is a temperature gradient of at least a few degrees."

Sulin Zhang, professor of engineering science and mechanics, Penn State is the other corresponding author on the paper that appears in Energy and Environmental Science. Zhang and his students were responsible for extensive computational work simulating the piezoelectric performance of the 3-D composite.

"We were able to show theoretically that the piezoelectric performance of nanoparticle/nanowire composites is critically limited by the large disparity in stiffness of the polymer matrix and piezoceramics, but the 3-D composite foam is not limited by stiffness," said Zhang. "This is the fundamental difference between these composite materials, which speaks to the innovation of this new 3-D composite. Our extensive simulations further demonstrate this idea."

Currently, Wang and his collaborators are working with lead-free and more environmentally friendly alternatives to the current lead-zirconium-titanate ceramic.

"This is a very general method," said Wang. "This is to demonstrate the concept, based on Bob Newnham's work. It is good to continue the work of a Penn State legend and to advance this field."

Additional authors on the article, "Flexible three-dimensional interconnected piezoelectric ceramic foam based composites for highly efficient concurrent mechanical and thermal energy harvesting," are co-lead authors Guangzu Zhang, formerly in Wang's group and now at Huazhong University of Science and Technology, China; and Peng Zhao, a doctoral student in Zhang's group. Other contributors are Xiaoshin Zhang, Kuo Han, Tiankai Zhao, Yong Zhang, Chang Kyu Jeong and Shenglin Jiang.

Related Links
Penn State
Powering The World in the 21st Century at Energy-Daily.com

Tweet

Thanks for being there;
We need your help. The SpaceDaily news network continues to grow but revenues have never been harder to maintain.

With the rise of Ad Blockers, and Facebook - our traditional revenue sources via quality network advertising continues to decline. And unlike so many other news sites, we don't have a paywall - with those annoying usernames and passwords.

Our news coverage takes time and effort to publish 365 days a year.

If you find our news sites informative and useful then please consider becoming a regular supporter or for now make a one off contribution.

SpaceDaily Monthly Supporter
$5+ Billed Monthly

paypal only

SpaceDaily Contributor
$5 Billed Once

credit card or paypal

Simple equation directs creation of clean-energy catalysts
Lincoln NB (SPX) May 15, 2018
New guidelines laid down by Nebraska and Chinese researchers could steer the design of less costly, more efficient catalysts geared toward revving up the production of hydrogen as a renewable fuel. Nebraska's Xiao Cheng Zeng and colleagues have identified several overlooked factors critical to the performance of single-atom catalysts: individual atoms, usually metallic and anchored by surrounding molecular frameworks, that kick-start and accelerate chemical reactions. The team folded those v ... read more